ABOUT V2100 SYSTEM FARM EQUIPMENT SPRAY
Provide long-lasting color and protection to outdoor machinery with Rust-Oleum High Performance V2100 System Farm Equipment Spray. This high-gloss industrial enamel comes in a full range of original-equipment colors and produces a tough, durable finish.
- Tough, professional finish—superior resistance to chipping, cracking and peeling
- High-output tip covers 50% faster; dries in only 20 minutes to touch
- Withstands heat to 200° F
- Meets USDA requirements for incidental food contact; VOC-compliant nationwide
For Best Results
- For large projects, apply using the High Performance Comfort Grip
SURFACE PREPARATION
Remove all dirt, grease, oil, salt and chemical contaminants
by washing the surface with a commercial detergent, or
other suitable cleaning method. Rinse with fresh water and
allow to thoroughly dry. Remove loose paint and rust with a
wire brush or sandpaper. Previously coated surfaces must
be sound and in good condition. Smooth, hard, or glossy
finishes should be scarified by sanding to create a surface
profile.
WARNING! If you scrape, sand or remove old paint from any
surface, you may release lead paint dust. LEAD IS TOXIC.
EXPOSURE TO LEAD DUST CAN CAUSE SERIOUS
ILLNESS, SUCH AS BRAIN DAMAGE; ESPECIALLY IN
CHILDREN. PREGNANT WOMEN SHOULD ALSO AVOID
EXPOSURE. Wear a NIOSH approved respirator to control
lead exposure. Clean up carefully with a HEPA vacuum and
a wet mop. Before you start, find out how to protect yourself
and your family by contacting the National Lead Information
Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
STEEL: Hand tool (SSPC-SP-2) or power tool (SSPC-SP-3)
clean to remove loose rust, mill scale, and deteriorated
previous coatings. For best results, use Red Primer on
sound rusted or clean metal before the application of a finish
coat or intermediate primer.
PREVIOUSLY COATED: Previously coated surfaces must
be sound and in good condition. Smooth, hard, or glossy
finishes should be scarified by sanding to create a surface
profile.
GALVANIZED STEEL: New galvanized steel may contain a
surface wax or oil from the fabricator. This must be removed
with Krud Kutter® Original Cleaner/Degreaser, commercial
detergent or other suitable cleaner. NOTE: Only the V2100
System Galvanizing Compounds are to be used on
galvanized steel. Do not use any other of the V2100 System
Primers or Finish Colors.
WEATHERED GALVANIZED STEEL: Remove loose rust
and stains by hand tool (SSPC-SP-2) or power tool
(SSPC-SP-3) prior to application of the Cold Galvanizing
Compound
Use when temperature is above 50°F (10°C) and humidity is
below 85% to ensure proper drying. Surface temperature
must be between 50-100°F (10-38°C).
Use primer on bare or rusted surfaces. Do not use any
primer with V2116838 High Temperature Aluminum,
V2176838 High Temperature Black, V2117838 Bright
Galvanizing Compound or V2185838 Cold Galvanizing
Compound.
Protect surrounding surfaces from overspray. Overspray can
carry a significant distance. Shake can for one minute after
mixing ball is heard. Hold can 10-14 inches from surface.
Apply several light coats a few minutes apart to avoid drips
and runs.
DRY & RECOAT TIMES
Recoat within 1 hour or after 24 hours. Allow more time in
cooler temperatures.
CLEAN-UP
Wipe off tip before storing. Clean-up wet paint with xylene or
mineral spirits. Note: Clean-up wet V2115838 Silver
Aluminum with xylol or acetone. Properly discard empty
container. Do not burn or place in trash compactor. Empty
container can be recycled.
CLOGGING
If the valve clogs, twist and pull off spray tip and rinse in a
solvent such as mineral spirits. Do not insert any object into
can valve opening.